NITROUS OXIDE ( nos / n2o ) advice forum

View unanswered posts | View active topics

Board index » Related to: Nitrous Oxide / N20 / NOS » Motorcycle Nitrous Oxide (NOS / N2O) Discussion

All times are UTC

MAX Extreme V2 Motorcycle connecions

Moderators: Brett928S2, T.F.S., Noswizard, chip

Page 1 of 1

[ 2 posts ]

Print view

Previous topic | Next topic

Author

Message

Brice Workhorse

Post subject: MAX Extreme V2 Motorcycle connecions

Posted: Sun May 13, 2018 10:06 am

Newbie

Joined: Wed May 09, 2018 5:05 pm
Posts: 1

Hi Everybody,
I'm Brice from Belgium, pro builder of performances bikes.
I'm now finishing a drag bike for 200m series. Besed on a Yamaha MT-07 Engine. Twin Cylindre.

I have some trouble with the connection of Max Extreme V2. I can not have the RPM infos.
So i have try to connect the controler to one of the spark wire to get a signal but nothing appear on the screen.
I also tryed from the 2 wires comming from the ecu (supposed to send the signal to the original tachometer) but nothing append.

So for the moment i only have the trottle position ok. The Nos pressure also.
Every good advice is really welcome.

One other point is:
For the champ the Power/weight Ratio is quiet low 0.64hp/kg.
The build is 140kg :salute:

Top

Noswizard

Post subject: Re: MAX Extreme V2 Motorcycle connecions

Posted: Wed May 30, 2018 11:41 pm

Site Admin

Joined: Thu Feb 03, 2005 6:07 pm
Posts: 18701
Location: Doncaster

Brice Workhorse wrote:

Hi Everybody,
I'm Brice from Belgium, pro builder of performances bikes.
Hi Brice and welcome to my forum. Very sorry for the delay but I'm so busy that I can't find enough time to look at my forum very often and for some reason it didn't inform me that your post had been made.
If you need any tech advice in future and you don't get an immediate response here, please drop me a line to enquiries@noswizard.com or contact via our Facebook page.

I have some trouble with the connection of Max Extreme V2. I can not have the RPM infos.
Every good advice is really welcome.
All Max instructions are listed on this page;
http://www.noswizard.com/max-instructions
The specific instruction sheet you need to sort the RPM issue is this one;
http://www.noswizard.com/pdf/b%20How%20 ... switch.pdf

If you still have problems after acting on these instructions, please get back to me as mentioned above

One other point is:
For the champ the Power/weight Ratio is quiet low 0.64hp/kg.
The build is 140kg :salute:

So i'm limited to 90hp. Today the engine is 81hp at 11krpm.
I use a Racepro 150 kit for twin.
So i'm wondering if it's possible to get a lot of torque with the nitrous and staying under the 90hp?
The torque curve is falling from 7krpm
With the Max you and the appropriate jets, you could achieve a FLAT torque curve at the maximum possible torque limit, without increasing eth peak power above the 90 HP, if you wanted and if you could use it. All you ned to do is select the right jets and the right settings.

Thanks

My pleasure.

_________________
Regards

Trev (The WIZARD of NOS)

30 years of nitrous experience and counting!!!!

Top

Page 1 of 1

[ 2 posts ]

Board index » Related to: Nitrous Oxide / N20 / NOS » Motorcycle Nitrous Oxide (NOS / N2O) Discussion

All times are UTC

Who is online

Users browsing this forum: No registered users and 12 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:

MAX Extreme V2 Motorcycle connecions

Advertisement

Who is online