NITROUS OXIDE ( nos / n2o ) advice forum

Nitrous Oxide ( NOS / N20 ) Forum
 
It is currently Fri Jul 19, 2019 6:30 pm

All times are UTC




Post new topic Reply to topic  [ 6 posts ] 
Author Message
 Post subject: advice wanted
PostPosted: Fri Nov 15, 2013 6:36 pm 
Offline
Newbie

Joined: Thu Nov 14, 2013 9:45 pm
Posts: 4
hi started to build nos set up for my yzf1000r have bottle ,and two newly refurbished solenoids,runnuing standard air box with kn,dynojet stage 1 kit,akrapovic system, thinking of similiar set up to sb50 kit,any suggestions and advice on best way to set this up only going to go up to 50 bhp shot , thinking of purge kit as well cheers in advance :)


Top
 Profile  
Reply with quote  

Advertisement

Wizards of NOS Nitrous Oxide Systems
 Post subject: Re: advice wanted
PostPosted: Sun Nov 17, 2013 1:18 pm 
Offline
Site Admin

Joined: Thu Feb 03, 2005 6:07 pm
Posts: 18701
Location: Doncaster
wadsta325 wrote:
hi started to build nos set up for my yzf1000r have bottle ,and two newly refurbished solenoids,runnuing standard air box with kn,dynojet stage 1 kit,akrapovic system, thinking of similiar set up to sb50 kit,any suggestions and advice on best way to set this up only going to go up to 50 bhp shot , thinking of purge kit as well cheers in advance :)

If you use ALL WON parts you shouldn't need a purge (unless you want to pose with it) and always start at 25 bhp before stepping up to 50.
Other than that all you need to do is go to our instructions page and select the SB50 wet page.

_________________
Regards

Trev (The WIZARD of NOS)

30 years of nitrous experience and counting!!!!


Top
 Profile  
Reply with quote  
 Post subject: Re: advice wanted
PostPosted: Sun Nov 17, 2013 1:46 pm 
Offline
Newbie

Joined: Thu Nov 14, 2013 9:45 pm
Posts: 4
Noswizard wrote:
wadsta325 wrote:
hi started to build nos set up for my yzf1000r have bottle ,and two newly refurbished solenoids,runnuing standard air box with kn,dynojet stage 1 kit,akrapovic system, thinking of similiar set up to sb50 kit,any suggestions and advice on best way to set this up only going to go up to 50 bhp shot , thinking of purge kit as well cheers in advance :)

If you use ALL WON parts you shouldn't need a purge (unless you want to pose with it) and always start at 25 bhp before stepping up to 50.
Other than that all you need to do is go to our instructions page and select the SB50 wet page.

thanks for getting back ,were is best place for nitrous venom injector {can it go before filter or will that freeze filter or should it go between filter and carbs},and really want purge kit ,but how would i go about installing ,like posing when on show , :)


Top
 Profile  
Reply with quote  
 Post subject: Re: advice wanted
PostPosted: Sun Nov 17, 2013 9:58 pm 
Offline
Site Admin

Joined: Thu Feb 03, 2005 6:07 pm
Posts: 18701
Location: Doncaster
[quote="wadsta325"] thanks for getting back ,were is best place for nitrous venom injector
I'd need to see the induction system layout to advise you on that.

can it go before filter or will that freeze filter
Yes that MIGHT be OK as long as it's not a paper element but again I could be more definite if I can see the induction layout.

or should it go between filter and carbs
NO, if they're not suitable to be located in the airbox they will HAVE TO BE located between the carbs and the heads.

and really want purge kit ,but how would i go about installing ,like posing when on show , :)
Do you have the early type Pulsoids or X-10s

_________________
Regards

Trev (The WIZARD of NOS)

30 years of nitrous experience and counting!!!!


Top
 Profile  
Reply with quote  
 Post subject: Re: advice wanted
PostPosted: Mon Nov 18, 2013 9:51 pm 
Offline
Newbie

Joined: Thu Nov 14, 2013 9:45 pm
Posts: 4
Noswizard wrote:
wadsta325 wrote:
thanks for getting back ,were is best place for nitrous venom injector
I'd need to see the induction system layout to advise you on that.

can it go before filter or will that freeze filter
Yes that MIGHT be OK as long as it's not a paper element but again I could be more definite if I can see the induction layout.

or should it go between filter and carbs
NO, if they're not suitable to be located in the airbox they will HAVE TO BE located between the carbs and the heads.

and really want purge kit ,but how would i go about installing ,like posing when on show , :)
Do you have the early type Pulsoids or X-10s

thanks again,will take pics when apart,its a k n filter,and early type pulsoids cheers :)


Top
 Profile  
Reply with quote  
 Post subject: Re: advice wanted
PostPosted: Tue Nov 19, 2013 2:08 am 
Offline
Site Admin

Joined: Thu Feb 03, 2005 6:07 pm
Posts: 18701
Location: Doncaster
can it go before filter or will that freeze filter
Yes that MIGHT be OK as long as it's not a paper element but again I could be more definite if I can see the induction layout.
As you have a K&N filter element you'll be OK to blow nitrous through it.


and really want purge kit ,but how would i go about installing ,like posing when on show , :)
Do you have the early type Pulsoids or X-10s
thanks again,will take pics when apart,its a k n filter,and early type pulsoids cheers :)
In that case we'd supply you with a T-piece that you'd connect before the main Pusloid in the feed pipe and the spare T leg would run to the Purge solenoid.

_________________
Regards

Trev (The WIZARD of NOS)

30 years of nitrous experience and counting!!!!


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

  • Advertisement
Wizards of NOS Sparkplugs
Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group  
Design By Poker Bandits